5x 36v 48ah 1.78kWh SPIM08HP Lithium Power Modules

All 5 batteries are perfectly balanced and come with the complete steel enclosures.

 Each battery contains 60 SPIM08HP 3.7v 8ah cells, busbars, holders, and already in 10s6p 36v configuration with proper compression and mounting brackets. You are basically getting 30x of the 2p 3.7v 16ah cell modules in each battery, 150 total. You even get posts to add your BMS balance leads with ring terminals. This module is built to push 300 amps continuous and can pulse over 600 amps! This is a true power module, if you need a lot of power in a small space this is what you want. Or if you want to power a forklift, golf cart, EV, high power E-bikes, etc. This one battery offers more than enough power to push a standard 36v golf cart. We actually have 2 of these in parallel running one of our forklifts. Always use a BMS. You can easily make a 20s 72v module with 2 of these in series.

If you break these down to cell level you will get 50x 3.7v 16ah cell bricks or break them down further to the 8ah cells and you'll have 100 of them. Excellent value in this lot.

This is the most economic friendly golf cart or forklift build with BMS protection. Many customers add a 200a 10s lithium ion BMS to run their golf carts.

You also get 2 12v fans in each module. If you want you can actually set up a temperature system that triggers the fans on and off. Each fan has a positive and negative wire. To power the fans with this battery you can connect the fans in series to make a 24v fan system. Use a temperature sensor to trigger the fans on and off. The fans will blow air through the enclosure as they are built for that. You can also add a heating element to these batteries which we also sell and they fit inside the hole where the fans are. In theory you could have over temp trigger just the fans and under temp trigger the fans and heating element.

These were used as backup starting power for generators. Therefore these have not cycled too many times.

The fan assembly unscrews within seconds if you want to remove that part. The enclosure is just screws as well. We recommend keeping the enclosure together because it is steel and adds a nice layer of safety. Just remove the top of the case to gain access to add your BMS.

Each module weighs 75 lbs.
Module Dimensions 24" x 9" x 6" (add an inch for brackets and wiring clearance)
Fully charged voltage 42v (4.2v per cell)
Fully discharged voltage 28v (2.8v per cell)

The busbars are copper and depending on the temperature amperage rating you can easily push much higher than we stated earlier. The cells themselves being in 6p configuration in theory can be charged up to 720 amps and can discharge at 1200 amps. Of course we don't recommend to push any battery to their maximum levels. Also these are not your typical 300-800 cycle lithium cells, these are rated for over 2000 cycles and many of our customers have built these cells into their own modules before we were finally able to negotiate getting the entire modules with the busbars and holders.

CHECK OUT THE SPECS BELOW, THESE ARE REAL SPECS FOR THE INDIVIDUAL CELLS.

Material Li-ion

Typical capacity 8-9AH
Nominal Voltage 3.7V
Weight around 300g
Dimensions of cell body: 9x138X190mm
Dimensions of cell with tabs 9x138X210mm

Dimensions of cell holder:6 & 5/8th x 5 & 5/8th by 3/8th inches 

Internal Resistance ≤0.8mΩ

Max Charge Rate 120A
Recommend Continuous Discharge Rate 200A
Pulse Discharge Rate（3 seconds） 400A
Fully Charged voltage 4.2V
Discharge cut off voltage 2.5V
Working Charge Temp 0~50°C
Working Discharge Temp –20°C~50°C
Storage Temperature –20°C~50°C
 
Applications
e-bikes, powerwalls, car audio, golf
carts, forklifts, UPS, solar system, etc.
 
Cycle life
2000 cycles to 80% with 100% DOD
under normal temperature
 
Advantages
safety, environment-friendly, high
discharge current, low capacity loss,
super-long cycle life.

Auction Rules:

1. You must create an account or sign in to place a bid. This is to ensure the integrity of the auction.
2. Popcorn bidding is enabled to eliminate last second bids. If a bid is placed last second the time of the auction will extend for 2 minutes. If you get outbid last second you will have 2 minutes to place another bid.
3. If you win the auction an email will be immediately and automatically sent to you. If you want to set up your own shipping just choose local pickup.
4. The freight quotes in our estimator are tied into our account so they are the actual rates we get. If you win more than 1 auction of course the freight cost per pallet will be cheaper when we combine the shipment into one.
5. Local pickups Monday thru Friday 8am-5pm at 1375b Adams Rd Bensalem, PA. 19020. Weekend pickup by appointment only.
6. Our email is sales@batteryhookup.com. Phone number is 215-383-9009.
7. All auctions are final and as-is. We do our best to accurately and honestly describe the products in the auction to eliminate guessing and uncertainty.

Our goal is to create a superior auction experience. The ability to calculate freight cost before bidding was a very important feature when some other auction platforms don't offer shipping at all. We also try to palletize similar items and take the time to spot test and give a more detailed description.