36v 48ah 1.78kWh POWER Module - 60x SPIM08HP
36v 48ah 1.78kWh POWER Module - 60x SPIM08HP
36v 48ah 1.78kWh POWER Module - 60x SPIM08HP
Battery Hookup

36v 48ah 1.78kWh POWER Module - 60x SPIM08HP

Regular price $299.99 $0.00 Unit price per
For those of you looking for SPIM08HP cells this is the product you have been waiting for.

You can easily make these into 7s6p 24v pack and 14s6p 48v packs if you order enough modules. We have companies already building these into powerwalls of different voltages. 7 modules you can build a 48v 12.76kWh module that will all ship on the same pallet without any waste or extra unused cells. You can also cut the busbars and make whatever you want. Just remember when you cut the busbars you cut out at least 1/8" so when you build it back the busbars don't touch again.

This product must ship freight which is calculated. The more you buy the cheaper it gets per battery for freight. We include residential and lift gate service. Or you can pick up for free from our Bensalem, PA location.

60 SPIM08HP cells, busbars, holders, and already in 10s6p 36v configuration with proper compression and mounting brackets. You even get posts to add your BMS balance leads with ring terminals. This module is built to push 500 amps continuous and can pulse over 1000 amps and it comes out to $5.00 per cell with busbars and holders! This is a true power module, if you need a lot of power in a small space this is what you want. Or if you want to power a forklift, golf cart, EV, high power E-bikes, etc. This one battery offers more than enough power to push a standard 36v golf cart. We actually have 2 of these in parallel running one of our forklifts. You should always use a BMS but many customers use the BMS for charge only then use a voltage display and run the discharge direct. You can easily make a 20s 72v module with 2 of these in series.

These were used as backup starting power for cold climate generators. Therefore these have not cycled too many times. Likely less than 1 full cycle.

Module weight is 65 lbs.
Pack Dimensions 24" x 9" x 6" (add an inch for brackets and wiring clearance)
Fully charged voltage 42v
Fully discharged voltage 28v

The busbars are copper and depending on the temperature amperage rating you can easily push much higher than we stated earlier. The cells themselves being in 6p configuration in theory can be charged up to 720 amps and can discharge at 1200 amps. Of course we don't recommend to push any battery to their maximum levels. Also these are not your typical 300-800 cycle lithium cells, these are rated for over 2000 cycles and many of our customers have built these cells into their own modules before we were finally able to negotiate getting the entire modules with the busbars and holders.

CHECK OUT THE SPECS BELOW, THESE ARE REAL SPECS FOR THE INDIVIDUAL CELLS.

 

Material Li-ion

Typical capacity 8-9AH
Nominal Voltage 3.7V
Weight around 300g
Dimensions of cell body: 9x138X190mm
Dimensions of cell with tabs 9x138X210mm

Dimensions of cell holder:6 & 5/8th x 5 & 5/8th by 3/8th inches 

Internal Resistance ≤0.8mΩ

Max Charge Rate 120A
Recommend Continuous Discharge Rate 200A
Pulse Discharge Rate(3 seconds) 400A
Fully Charged voltage 4.2V
Discharge cut off voltage 2.5V
Working Charge Temp 0~50°C
Working Discharge Temp –20°C~50°C
Storage Temperature –20°C~50°C
 
Applications
e-bikes, powerwalls, car audio, golf
carts, forklifts, UPS, solar system, etc.
 
Cycle life
2000 cycles to 80% with 100% DOD
under normal temperature
 
Advantages
safety, environment-friendly, high
discharge current, low capacity loss,
super-long cycle life.


Share this Product